Merge branch 'master' of https://github.com/suchmememanyskill/CYD-Klipper-Display

It's "WiFiClient..." and not "WifiClient..."

Signed-off-by: Stefan Naewe <stefan.naewe@gmail.com>

.github/workflows/compile.yaml

@@ -33,7 +33,7 @@ jobs:
 
       - uses: actions/setup-python@v5
         with:
-          python-version: '3.9'
+          python-version: '3.13'
 
       - name: Install PlatformIO Core
         run: pip install --upgrade platformio esptool

CYD-Klipper/.vscode/settings.json

@@ -48,7 +48,8 @@
         "stdexcept": "cpp",
         "streambuf": "cpp",
         "cinttypes": "cpp",
-        "typeinfo": "cpp"
+        "typeinfo": "cpp",
+        "*.tpp": "cpp"
     },
     "cmake.configureOnOpen": false
 }

CYD-Klipper/boards/esp32-JC3248W535C.json

@@ -0,0 +1,69 @@
+{
+    "name": "ESP32-JC3248W535C",
+    "url":  "https://www.aliexpress.com/item/1005007566315926.html",     
+    "vendor": "Guition",
+  
+    "build": {
+      "arduino": {
+        "ldscript": "esp32s3_out.ld",
+        "memory_type": "qio_opi",
+        "partitions": "default_16MB.csv"
+      },
+      "core":     "esp32",
+      "mcu":      "esp32s3",
+      "variant":  "esp32s3",
+  
+      "f_cpu":    "240000000L",  
+      "f_flash":  "80000000L",   
+      "extra_flags": [
+        "-DLCD_WIDTH=320",
+        "-DLCD_HEIGHT=480",
+        "-DCYD_SCREEN_GAP_PX=8",
+        "-DCYD_SCREEN_FONT=lv_font_montserrat_14",
+        "-DCYD_SCREEN_FONT_SMALL=lv_font_montserrat_12",
+        "-DCYD_SCREEN_WIDTH_PX=LCD_WIDTH",
+        "-DCYD_SCREEN_HEIGHT_PX=LCD_HEIGHT",
+        "-DCYD_SCREEN_SIDEBAR_SIZE_PX=50",
+        "-DCYD_SCREEN_MIN_BUTTON_HEIGHT_PX=45",
+        "-DCYD_SCREEN_MIN_BUTTON_WIDTH_PX=45",
+        "-DLCD_CS=45",
+        "-DLCD_CLK=47",
+        "-DLCD_D0=21",
+        "-DLCD_D1=48",
+        "-DLCD_D2=40",
+        "-DLCD_D3=39",
+        "-DLCD_RST=-1",           
+        "-DLCD_DC=8",            
+        "-DTOUCH_SDA=4",
+        "-DTOUCH_SCL=8",
+        "-DTOUCH_ADDR=0x3B",
+        "-DLCD_BL_PIN=1",
+        "-DCYD_BOARD_JC3248W535C",
+        "-DCYD_SCREEN_DISABLE_TOUCH_CALIBRATION",
+        "-DUSER_SETUP_LOADED",
+        "-DARDUINO_USB_CDC_ON_BOOT=1",
+        "-DCYD_SCREEN_VERTICAL=1"
+      ],
+      "flash_mode": "qio",
+
+      "hwids": [
+        [
+          "0X303A",
+          "0x1001"
+        ]
+      ]
+    },
+  
+    "upload": {
+      "flash_size": "16MB",
+      "flash_mode": "qio",
+      "maximum_ram_size": 327680,
+      "maximum_size": 16777216,
+      "require_upload_port": true,
+      "speed": 921600
+    },
+  
+    "frameworks":  ["arduino", "espidf"],
+    "connectivity": ["wifi", "bluetooth"]
+  }
+  

CYD-Klipper/boards/esp32-JC4827W543C.json

@@ -0,0 +1,66 @@
+{
+    "name": "ESP32-JC4827W543C",
+    "url":  "https://s.click.aliexpress.com/e/_oEcVE26",     
+    "vendor": "Guition",
+  
+    "build": {
+      "arduino": {
+        "ldscript": "esp32s3_out.ld",
+        "memory_type": "qio_opi"
+      },
+      "core":     "esp32",
+      "mcu":      "esp32s3",
+      "variant":  "esp32s3",
+  
+      "f_cpu":    "240000000L",  
+      "f_flash":  "80000000L",   
+      "extra_flags": [
+        "-DBOARD_HAS_PSRAM",
+        "-DLCD_WIDTH=480",
+        "-DLCD_HEIGHT=270",
+        "-DCYD_SCREEN_GAP_PX=8",
+        "-DCYD_SCREEN_FONT=lv_font_montserrat_14",
+        "-DCYD_SCREEN_FONT_SMALL=lv_font_montserrat_12",
+        "-DCYD_SCREEN_WIDTH_PX=480",
+        "-DCYD_SCREEN_HEIGHT_PX=272",
+        "-DCYD_SCREEN_SIDEBAR_SIZE_PX=50",
+        "-DCYD_SCREEN_MIN_BUTTON_HEIGHT_PX=40",
+        "-DCYD_SCREEN_MIN_BUTTON_WIDTH_PX=45",
+        "-DLCD_CS=45",
+        "-DLCD_CLK=47",
+        "-DLCD_D0=21",
+        "-DLCD_D1=48",
+        "-DLCD_D2=40",
+        "-DLCD_D3=39",
+        "-DLCD_RST=-1",           
+        "-DLCD_DC=8",            
+        "-DLCD_BL_PIN=1",
+        "-DCYD_BOARD_JC4827W543C",
+        "-DCYD_SCREEN_DISABLE_TOUCH_CALIBRATION",
+        "-DUSER_SETUP_LOADED",
+        "-DARDUINO_USB_CDC_ON_BOOT=1",
+        "-DCYD_S3"
+      ],
+      "flash_mode": "qio",
+
+      "hwids": [
+        [
+          "0X303A",
+          "0x1001"
+        ]
+      ]
+    },
+  
+    "upload": {
+      "flash_size": "4MB",
+      "flash_mode": "qio",
+      "maximum_ram_size": 327680,
+      "maximum_size": 16777216,
+      "require_upload_port": true,
+      "speed": 921600
+    },
+  
+    "frameworks":  ["arduino", "espidf"],
+    "connectivity": ["wifi", "bluetooth"]
+  }
+  

CYD-Klipper/boards/esp32-JC8048W550.json

@@ -0,0 +1,142 @@
+{
+  "build": {
+    "arduino": {
+      "ldscript": "esp32s3_out.ld",
+      "partitions": "default_16MB.csv",
+      "memory_type": "qio_opi"
+    },
+    "core": "esp32",
+    "extra_flags": [
+      "'-D ARDUINO_ESP32S3_DEV'",
+      "'-D BOARD_HAS_PSRAM'",
+      "'-D ARDUINO_USB_MODE=1'",
+      "'-D ARDUINO_RUNNING_CORE=1'",
+      "'-D ARDUINO_EVENT_RUNNING_CORE=1'",
+      "'-D ARDUINO_USB_CDC_ON_BOOT=0'",
+      "'-D JC8048W550'",
+      "'-D LCD_WIDTH=800'",
+      "'-D LCD_HEIGHT=480'",
+      "'-D LVGL_BUFFER_PIXELS=(LCD_WIDTH*LCD_HEIGHT)'",
+      "'-D LVGL_BUFFER_MALLOC_FLAGS=(MALLOC_CAP_SPIRAM|MALLOC_CAP_8BIT)'",
+      "'-D GPIO_BCKL=2'",
+      "'-D LCD_ST7262_PAR'",
+      "'-D ST7262_PANEL_CONFIG_CLK_SRC=LCD_CLK_SRC_PLL160M'",
+      "'-D ST7262_PANEL_CONFIG_TIMINGS_PCLK_HZ=(14.2*1000000)'",
+      "'-D ST7262_PANEL_CONFIG_TIMINGS_H_RES=LCD_WIDTH'",
+      "'-D ST7262_PANEL_CONFIG_TIMINGS_V_RES=LCD_HEIGHT'",
+      "'-D ST7262_PANEL_CONFIG_TIMINGS_HSYNC_PULSE_WIDTH=4'",
+      "'-D ST7262_PANEL_CONFIG_TIMINGS_HSYNC_BACK_PORCH=8'",
+      "'-D ST7262_PANEL_CONFIG_TIMINGS_HSYNC_FRONT_PORCH=8'",
+      "'-D ST7262_PANEL_CONFIG_TIMINGS_VSYNC_PULSE_WIDTH=4'",
+      "'-D ST7262_PANEL_CONFIG_TIMINGS_VSYNC_BACK_PORCH=8'",
+      "'-D ST7262_PANEL_CONFIG_TIMINGS_VSYNC_FRONT_PORCH=8'",
+      "'-D ST7262_PANEL_CONFIG_TIMINGS_FLAGS_HSYNC_IDLE_LOW=false'",
+      "'-D ST7262_PANEL_CONFIG_TIMINGS_FLAGS_VSYNC_IDLE_LOW=false'",
+      "'-D ST7262_PANEL_CONFIG_TIMINGS_FLAGS_DE_IDLE_HIGH=false'",
+      "'-D ST7262_PANEL_CONFIG_TIMINGS_FLAGS_PCLK_ACTIVE_NEG=true'",
+      "'-D ST7262_PANEL_CONFIG_TIMINGS_FLAGS_PCLK_IDLE_HIGH=false'",
+      "'-D ST7262_PANEL_CONFIG_DATA_WIDTH=16'",
+      "'-D ST7262_PANEL_CONFIG_SRAM_TRANS_ALIGN=4'",
+      "'-D ST7262_PANEL_CONFIG_PSRAM_TRANS_ALIGN=64'",
+      "'-D ST7262_PANEL_CONFIG_HSYNC_GPIO_NUM=39'",
+      "'-D ST7262_PANEL_CONFIG_VSYNC_GPIO_NUM=41'",
+      "'-D ST7262_PANEL_CONFIG_DE_GPIO_NUM=40'",
+      "'-D ST7262_PANEL_CONFIG_PCLK_GPIO_NUM=42'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_R0=8'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_R1=3'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_R2=46'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_R3=9'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_R4=1'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_G0=5'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_G1=6'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_G2=7'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_G3=15'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_G4=16'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_G5=4'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_B0=45'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_B1=48'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_B2=47'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_B3=21'",
+      "'-D ST7262_PANEL_CONFIG_DATA_GPIO_B4=14'",
+      "'-D ST7262_PANEL_CONFIG_DISP_GPIO_NUM=GPIO_NUM_NC'",
+      "'-D ST7262_PANEL_CONFIG_FLAGS_DISP_ACTIVE_LOW=false'",
+      "'-D ST7262_PANEL_CONFIG_FLAGS_RELAX_ON_IDLE=false'",
+      "'-D ST7262_PANEL_CONFIG_FLAGS_FB_IN_PSRAM=true'",
+      "'-D BOARD_HAS_TOUCH'",
+      "'-D TOUCH_GT911_I2C'",
+      "'-D GT911_I2C_HOST=I2C_NUM_0'",
+      "'-D GT911_I2C_CONFIG_SDA_IO_NUM=19'",
+      "'-D GT911_I2C_CONFIG_SCL_IO_NUM=20'",
+      "'-D GT911_I2C_CONFIG_SDA_PULLUP_EN=GPIO_PULLUP_DISABLE'",
+      "'-D GT911_I2C_CONFIG_SCL_PULLUP_EN=GPIO_PULLUP_DISABLE'",
+      "'-D GT911_I2C_CONFIG_MASTER_CLK_SPEED=400000'",
+      "'-D GT911_I2C_CONFIG_CLK_FLAGS=I2C_SCLK_SRC_FLAG_FOR_NOMAL'",
+      "'-D GT911_IO_I2C_CONFIG_DEV_ADDR=ESP_LCD_TOUCH_IO_I2C_GT911_ADDRESS'",
+      "'-D GT911_IO_I2C_CONFIG_CONTROL_PHASE_BYTES=1'",
+      "'-D GT911_IO_I2C_CONFIG_DC_BIT_OFFSET=0'",
+      "'-D GT911_IO_I2C_CONFIG_LCD_CMD_BITS=16'",
+      "'-D GT911_IO_I2C_CONFIG_LCD_PARAM_BITS=0'",
+      "'-D GT911_IO_I2C_CONFIG_FLAGS_DC_LOW_ON_DATA=false'",
+      "'-D GT911_IO_I2C_CONFIG_FLAGS_DISABLE_CONTROL_PHASE=true'",
+      "'-D GT911_TOUCH_CONFIG_X_MAX=LCD_WIDTH'",
+      "'-D GT911_TOUCH_CONFIG_Y_MAX=LCD_HEIGHT'",
+      "'-D GT911_TOUCH_CONFIG_RST_GPIO_NUM=38'",
+      "'-D GT911_TOUCH_CONFIG_INT_GPIO_NUM=18'",
+      "'-D GT911_TOUCH_CONFIG_LEVELS_RESET=0'",
+      "'-D GT911_TOUCH_CONFIG_LEVELS_INTERRUPT=0'",
+      "'-D TOUCH_SWAP_XY=false'",
+      "'-D TOUCH_SWAP_X=false'",
+      "'-D TOUCH_SWAP_Y=false'",
+      "'-D BOARD_HAS_TF'",
+      "'-D TF_CS=10'",
+      "'-D TF_SPI_MOSI=11'",
+      "'-D TF_SPI_SCLK=12'",
+      "'-D TF_SPI_MISO=13'",
+      "-DCYD_SCREEN_HEIGHT_PX=LCD_HEIGHT",
+      "-DCYD_SCREEN_WIDTH_PX=LCD_WIDTH",
+      "-DROTATION_INVERTED=LV_DISP_ROT_180",
+      "-DROTATION_NORMAL=LV_DISP_ROT_NONE",
+      "-DCYD_SCREEN_GAP_PX=15",
+      "-DCYD_SCREEN_MIN_BUTTON_HEIGHT_PX=60",
+      "-DCYD_SCREEN_MIN_BUTTON_WIDTH_PX=60",
+      "-DCYD_SCREEN_FONT=lv_font_montserrat_22",
+      "-DCYD_SCREEN_FONT_SMALL=lv_font_montserrat_16",
+      "-DCYD_SCREEN_SIDEBAR_SIZE_PX=70",
+      "-DCYD_SCREEN_DRIVER_ESP32_SMARTDISPLAY=0",
+      "-DCYD_SCREEN_DISABLE_TOUCH_CALIBRATION=1"
+    ],
+    "f_cpu": "240000000L",
+    "f_flash": "80000000L",
+    "flash_mode": "qio",
+    "hwids": [
+      [
+        "0x303A",
+        "0x1001"
+      ]
+    ],
+    "mcu": "esp32s3",
+    "variant": "esp32s3"
+  },
+  "connectivity": [
+    "wifi"
+  ],
+  "debug": {
+    "openocd_target": "esp32s3.cfg"
+  },
+  "frameworks": [
+    "arduino",
+    "espidf"
+  ],
+  "name": "esp32-JC8048W550",
+  "upload": {
+    "flash_size": "16MB",
+    "maximum_ram_size": 327680,
+    "maximum_size": 16777216,
+    "use_1200bps_touch": true,
+    "wait_for_upload_port": true,
+    "require_upload_port": true,
+    "speed": 460800
+  },
+  "url": "https://www.aliexpress.com/item/1005006715581887.html",
+  "vendor": "Guition"
+}

CYD-Klipper/platformio.ini

@@ -111,9 +111,34 @@ board = esp32-CROWPANEL-35C
 lib_deps =
 	SPI
 	https://github.com/suchmememanyskill/lvgl
-	https://github.com/lovyan03/LovyanGFX@1.2.0
+	https://github.com/lovyan03/LovyanGFX@1.2.7
 	bblanchon/ArduinoJson@^7.0.0
 	plageoj/UrlEncode@^1.0.1
 	knolleary/PubSubClient@^2.8
 	WiFiClientSecure
 
+[env:esp32-JC8048W550]
+board = esp32-JC8048W550
+
+[env:ESP32-JC3248W535C]
+board = esp32-JC3248W535C
+lib_deps =
+    SPI
+    moononournation/GFX Library for Arduino
+    lvgl/lvgl@^8.4.0
+    plageoj/UrlEncode
+    bblanchon/ArduinoJson@^7.0.0
+	knolleary/PubSubClient@^2.8
+    WiFiClientSecure
+
+[env:esp32-JC4827W543C]
+board = esp32-JC4827W543C
+lib_deps =
+    SPI
+    https://github.com/moononournation/Arduino_GFX#v1.4.9
+	https://github.com/mmMicky/TouchLib#ccaedcd9155ef8a6560ae9f594ea92e32c68020f
+    lvgl/lvgl@^8.4.0
+    plageoj/UrlEncode
+    bblanchon/ArduinoJson@^7.0.0
+	knolleary/PubSubClient@^2.8
+    WiFiClientSecure

CYD-Klipper/src/core/bambu/bambu_printer_integration.hpp

@@ -2,7 +2,7 @@
 
 #include "../printer_integration.hpp"
 #include <ArduinoJson.h>
-#include <WifiClientSecure.h>
+#include <WiFiClientSecure.h>
 
 enum BambuSpeedProfile 
 {

CYD-Klipper/src/core/bambu/bambu_printer_panels.cpp

@@ -161,7 +161,7 @@ struct
     };
 } __internal_bambu_file_state = {};
 
-#define SET_BOOL_STATE(bool_name, func_name) static void func_name (lv_event_t * e) { auto state = lv_obj_get_state(lv_event_get_target(e)); bool_name = (state & LV_STATE_CHECKED == LV_STATE_CHECKED); }
+#define SET_BOOL_STATE(bool_name, func_name) static void func_name (lv_event_t * e) { bool_name = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED); }
 
 SET_BOOL_STATE(__internal_bambu_file_state.bambu_option_use_ams, set_bambu_option_use_ams)
 SET_BOOL_STATE(__internal_bambu_file_state.bambu_option_timelapse, set_bambu_option_timelapse)

CYD-Klipper/src/core/device/ESP32-JC3248W535C.cpp

@@ -0,0 +1,184 @@
+#ifdef CYD_BOARD_JC3248W535C
+
+#include "../screen_driver.h"
+#include <databus/Arduino_ESP32QSPI.h>
+#include <display/Arduino_AXS15231B.h>
+#include <canvas/Arduino_Canvas.h>
+#include "lvgl.h"
+#include "../lv_setup.h"
+#include "../../conf/global_config.h"
+#include <Wire.h>
+#define CPU_FREQ_HIGH 240
+#define CPU_FREQ_LOW 80
+
+struct TouchPoint {
+  uint8_t gesture;
+  uint8_t num;
+  uint8_t x_h : 4;
+  uint8_t _pad1 : 2;
+  uint8_t event : 2;
+  uint8_t x_l;
+  uint8_t y_h : 4;
+  uint8_t _pad2 : 4;
+  uint8_t y_l;
+} __attribute__((packed));
+
+static Arduino_ESP32QSPI qspiBus(
+    LCD_CS, LCD_CLK,
+    LCD_D0, LCD_D1,
+    LCD_D2, LCD_D3,
+    false);
+
+
+Arduino_GFX *gfx = new Arduino_AXS15231B(
+    &qspiBus, -1, 2, true,
+    LCD_WIDTH, LCD_HEIGHT,
+    0, 0, 0, 0);
+
+#ifdef CYD_SCREEN_VERTICAL
+    static bool horizontal = false;
+    static Arduino_Canvas canvas(CYD_SCREEN_WIDTH_PX, CYD_SCREEN_HEIGHT_PX, gfx, 0, 0);
+#else
+    static bool horizontal = true;
+    static Arduino_Canvas canvas(CYD_SCREEN_HEIGHT_PX, CYD_SCREEN_WIDTH_PX, gfx, 0, 0);
+
+#endif
+
+static lv_disp_draw_buf_t draw_buf;
+static lv_color_t *buf = nullptr;
+static lv_disp_t *main_disp = nullptr;
+
+
+void screen_setBrightness(uint8_t brightness)
+{
+    uint32_t duty = (4095UL * brightness) / 255UL;
+    ledcWrite(0, duty);
+}
+
+void screen_lv_flush(lv_disp_drv_t *disp, const lv_area_t *area, lv_color_t *color_p)
+{
+    int x = area->x1;
+    int y = area->y1;
+    int w = area->x2 - area->x1 + 1;
+    int h = area->y2 - area->y1 + 1;
+    canvas.draw16bitRGBBitmap(x, y, (uint16_t *)color_p, w, h);
+    canvas.flush();
+
+    lv_disp_flush_ready(disp);
+}
+
+// Reads 1 touch point from AXS15231B controller at I2C addr 0x3B
+bool read_touch(uint16_t &x, uint16_t &y) {
+  const uint8_t addr = 0x3B;
+
+  const uint8_t read_cmd[11] = {
+    0xB5, 0xAB, 0xA5, 0x5A, 0x00, 0x00,
+    0x00, 8, // length of expected reply (MSB, LSB)
+    0x00, 0x00, 0x00
+  };
+
+  Wire.beginTransmission(addr);
+  Wire.write(read_cmd, sizeof(read_cmd));
+  if (Wire.endTransmission(false) != 0) {
+    return false;
+  }
+
+  uint8_t data[8] = {0};
+  if (Wire.requestFrom(addr, (uint8_t)sizeof(data)) != sizeof(data)) {
+    return false;
+  }
+
+  for (uint8_t i = 0; i < sizeof(data); i++) {
+    data[i] = Wire.read();
+  }
+
+  TouchPoint *p = (TouchPoint *)data;
+
+  if (p->num > 0 && p->num <= 2) {
+    x = ((p->x_h & 0x0F) << 8) | p->x_l;
+    y = ((p->y_h & 0x0F) << 8) | p->y_l;
+
+    // Clamp to screen bounds
+    if (x >= CYD_SCREEN_WIDTH_PX) x = CYD_SCREEN_WIDTH_PX - 1;
+    if (y >= CYD_SCREEN_HEIGHT_PX) y = CYD_SCREEN_HEIGHT_PX - 1;
+    return true;
+  }
+
+  return false;
+}
+
+
+void screen_lv_touchRead(lv_indev_drv_t * /*indev_driver*/, lv_indev_data_t *data)
+{
+  uint16_t x, y;
+  if (read_touch(x, y)) {
+    x = min(x, uint16_t(CYD_SCREEN_WIDTH_PX - 1));
+    y = min(y, uint16_t(CYD_SCREEN_HEIGHT_PX - 1));
+    // Adjust coordinates based on screen rotation
+    if (global_config.rotate_screen) {
+      // Assuming rotation = 2 (180 degrees)
+      x = CYD_SCREEN_WIDTH_PX - x;
+      y = CYD_SCREEN_HEIGHT_PX - y;
+    }
+
+    data->state = LV_INDEV_STATE_PR;
+    data->point.x = x;
+    data->point.y = y;
+  } else {
+    data->state = LV_INDEV_STATE_REL;
+  }
+}
+
+void set_invert_display()
+{
+    gfx->invertDisplay(global_config.printer_config[global_config.printer_index].invert_colors);
+}
+
+void screen_setup()
+{
+    pinMode(LCD_BL_PIN, OUTPUT);
+    ledcSetup(0, 5000, 12);
+    ledcAttachPin(LCD_BL_PIN, 0);
+    screen_setBrightness(255);
+
+    // gfx->begin();
+    canvas.begin();
+    gfx->invertDisplay(true);  // OK after begin()
+    gfx->setRotation(global_config.rotate_screen ? 2 : 0);
+    canvas.fillScreen(0x0000);
+    canvas.flush();
+
+    Wire.begin(TOUCH_SDA, TOUCH_SCL);
+
+    lv_init();
+
+    // Allocate full canvas buffer for LVGL
+    buf = (lv_color_t *)heap_caps_malloc(
+        CYD_SCREEN_WIDTH_PX * CYD_SCREEN_HEIGHT_PX * sizeof(lv_color_t),
+        MALLOC_CAP_SPIRAM | MALLOC_CAP_8BIT);
+
+    assert(buf);
+
+    lv_disp_draw_buf_init(&draw_buf, buf, NULL, CYD_SCREEN_WIDTH_PX * CYD_SCREEN_HEIGHT_PX);
+
+    static lv_disp_drv_t disp_drv;
+    lv_disp_drv_init(&disp_drv);
+    disp_drv.flush_cb = screen_lv_flush;
+    disp_drv.draw_buf = &draw_buf;
+    
+    disp_drv.hor_res = CYD_SCREEN_WIDTH_PX;
+    disp_drv.ver_res = CYD_SCREEN_HEIGHT_PX;
+    if(horizontal){
+        main_disp = lv_disp_drv_register(&disp_drv);
+        lv_disp_set_rotation(main_disp, LV_DISP_ROT_90);
+    } else {
+        lv_disp_drv_register(&disp_drv);
+    }
+    static lv_indev_drv_t indev_drv;
+    lv_indev_drv_init(&indev_drv);
+    indev_drv.type = LV_INDEV_TYPE_POINTER;
+    indev_drv.read_cb = screen_lv_touchRead;
+    lv_indev_drv_register(&indev_drv);
+}   
+
+#endif // CYD_BOARD_JC3248W535C

CYD-Klipper/src/core/device/ESP32-JC4827W543C.cpp

@@ -0,0 +1,85 @@
+#ifdef CYD_BOARD_JC4827W543C
+
+#include "../screen_driver.h"
+#include <Arduino_GFX_Library.h>
+#include "lvgl.h"
+#include "../lv_setup.h"
+#include "../../conf/global_config.h"
+#include "ESP32-JC4827W543C_touch.h"
+#define CPU_FREQ_HIGH 240
+#define CPU_FREQ_LOW 80
+
+Arduino_DataBus *bus = new Arduino_ESP32QSPI(LCD_CS, LCD_CLK, LCD_D0, LCD_D1, LCD_D2, LCD_D3);
+Arduino_NV3041A *panel = new Arduino_NV3041A(bus, LCD_RST, 0, true);
+
+static lv_disp_draw_buf_t draw_buf;
+static lv_disp_drv_t disp_drv;
+static lv_color_t disp_draw_buf[LCD_WIDTH * 48];
+
+void screen_setBrightness(uint8_t brightness)
+{
+    uint32_t duty = 4095 * brightness / 255;
+    ledcWrite(0, duty);
+}
+
+void screen_lv_flush(lv_disp_drv_t *disp, const lv_area_t *area, lv_color_t *color_p)
+{
+    uint32_t w = (area->x2 - area->x1 + 1);
+    uint32_t h = (area->y2 - area->y1 + 1);
+
+    panel->startWrite();
+    panel->setAddrWindow(area->x1, area->y1, w, h);
+    panel->writePixels((uint16_t *)&color_p->full, w * h);
+    panel->endWrite();
+    
+    lv_disp_flush_ready(disp);
+}
+
+void IRAM_ATTR screen_lv_touchRead(lv_indev_drv_t *indev_driver, lv_indev_data_t *data)
+{
+    if (touch_has_signal() && touch_touched())
+    {
+        data->state = LV_INDEV_STATE_PR;
+        data->point.x = touch_last_x;
+        data->point.y = touch_last_y;
+    }
+    else
+    {
+        data->state = LV_INDEV_STATE_REL;
+    }
+}
+
+void set_invert_display()
+{
+    panel->invertDisplay(global_config.printer_config[global_config.printer_index].invert_colors);
+}
+
+void screen_setup()
+{
+    pinMode(LCD_BL_PIN, OUTPUT);
+    ledcSetup(0, 5000, 12);
+    ledcAttachPin(LCD_BL_PIN, 0);
+    screen_setBrightness(128);
+
+    panel->begin();
+    panel->setRotation(global_config.rotate_screen ? 2 : 0);
+
+    touch_init(panel->width(), panel->height(), panel->getRotation());
+    lv_init();
+
+    lv_disp_draw_buf_init(&draw_buf, disp_draw_buf, NULL, LCD_WIDTH * 48);
+    lv_disp_drv_init(&disp_drv);
+    disp_drv.flush_cb = screen_lv_flush;
+    disp_drv.draw_buf = &draw_buf;
+    disp_drv.hor_res = CYD_SCREEN_WIDTH_PX;
+    disp_drv.ver_res = CYD_SCREEN_HEIGHT_PX;
+    lv_disp_drv_register(&disp_drv);
+
+    static lv_indev_drv_t indev_drv;
+    lv_indev_drv_init(&indev_drv);
+    indev_drv.type = LV_INDEV_TYPE_POINTER;
+    indev_drv.read_cb = screen_lv_touchRead;
+    lv_indev_drv_register(&indev_drv);
+}
+
+#endif // CYD_BOARD_JC4827W543C

CYD-Klipper/src/core/device/ESP32-JC4827W543C_touch.h

@@ -0,0 +1,196 @@
+/*******************************************************************************
+ *
+ *  TouchLib     https://github.com/mmMicky/TouchLib
+ Add Library from ZIP: TouchLib-main.zip
+ *
+ * Touch libraries:
+ * XPT2046: https://github.com/PaulStoffregen/XPT2046_Touchscreen.git
+ *
+ * Capacitive touchscreen libraries
+ * TouchLib: https://github.com/mmMicky/TouchLib.git
+ ******************************************************************************/
+
+/* uncomment for XPT2046 */
+// #define TOUCH_XPT2046
+// #define TOUCH_XPT2046_SCK 12
+// #define TOUCH_XPT2046_MISO 13
+// #define TOUCH_XPT2046_MOSI 11
+// #define TOUCH_XPT2046_CS 38
+// #define TOUCH_XPT2046_INT 3
+// #define TOUCH_XPT2046_ROTATION 0
+// #define TOUCH_XPT2046_SAMPLES 50
+
+ //uncomment for most capacitive touchscreen
+ #define TOUCH_MODULES_GT911 // GT911 / CST_SELF / CST_MUTUAL / ZTW622 / L58 / FT3267 / FT5x06
+ #define TOUCH_MODULE_ADDR GT911_SLAVE_ADDRESS1 // CTS328_SLAVE_ADDRESS / L58_SLAVE_ADDRESS / CTS826_SLAVE_ADDRESS / CTS820_SLAVE_ADDRESS / CTS816S_SLAVE_ADDRESS / FT3267_SLAVE_ADDRESS / FT5x06_ADDR / GT911_SLAVE_ADDRESS1 / GT911_SLAVE_ADDRESS2 / ZTW622_SLAVE1_ADDRESS / ZTW622_SLAVE2_ADDRESS
+ #define TOUCH_SCL 4
+ #define TOUCH_SDA 8
+ #define TOUCH_RES 38
+ #define TOUCH_INT 3
+
+// Please fill below values from Arduino_GFX Example - TouchCalibration
+bool touch_swap_xy = false;
+int16_t touch_map_x1 = -1;
+int16_t touch_map_x2 = -1;
+int16_t touch_map_y1 = -1;
+int16_t touch_map_y2 = -1;
+
+int16_t touch_max_x = 0, touch_max_y = 0;
+int16_t touch_raw_x = 0, touch_raw_y = 0;
+int16_t touch_last_x = 0, touch_last_y = 0;
+
+#if defined(TOUCH_XPT2046)
+#include <XPT2046_Touchscreen.h>
+#include <SPI.h>
+XPT2046_Touchscreen ts(TOUCH_XPT2046_CS, TOUCH_XPT2046_INT);
+
+#elif defined(TOUCH_MODULE_ADDR) // TouchLib
+#include <Wire.h>
+#include <TouchLib.h>
+TouchLib touch(Wire, TOUCH_SDA, TOUCH_SCL, TOUCH_MODULE_ADDR);
+
+#endif // TouchLib
+
+void touch_init(int16_t w, int16_t h, uint8_t r)
+{
+  touch_max_x = w - 1;
+  touch_max_y = h - 1;
+  if (touch_map_x1 == -1)
+  {
+    switch (r)
+    {
+    case 3:
+      touch_swap_xy = true;
+      touch_map_x1 = touch_max_x;
+      touch_map_x2 = 0;
+      touch_map_y1 = 0;
+      touch_map_y2 = touch_max_y;
+      break;
+    case 2:
+      touch_swap_xy = false;
+      touch_map_x1 = touch_max_x;
+      touch_map_x2 = 0;
+      touch_map_y1 = touch_max_y;
+      touch_map_y2 = 0;
+      break;
+    case 1:
+      touch_swap_xy = true;
+      touch_map_x1 = 0;
+      touch_map_x2 = touch_max_x;
+      touch_map_y1 = touch_max_y;
+      touch_map_y2 = 0;
+      break;
+    default: // case 0:
+      touch_swap_xy = false;
+      touch_map_x1 = 0;
+      touch_map_x2 = touch_max_x;
+      touch_map_y1 = 0;
+      touch_map_y2 = touch_max_y;
+      break;
+    }
+  }
+
+#if defined(TOUCH_XPT2046)
+  SPI.begin(TOUCH_XPT2046_SCK, TOUCH_XPT2046_MISO, TOUCH_XPT2046_MOSI, TOUCH_XPT2046_CS);
+  ts.begin();
+  ts.setRotation(TOUCH_XPT2046_ROTATION);
+
+#elif defined(TOUCH_MODULE_ADDR) // TouchLib
+  // Reset touchscreen
+#if (TOUCH_RES > 0)
+  pinMode(TOUCH_RES, OUTPUT);
+  digitalWrite(TOUCH_RES, 0);
+  delay(200);
+  digitalWrite(TOUCH_RES, 1);
+  delay(200);
+#endif
+  Wire.begin(TOUCH_SDA, TOUCH_SCL);
+  touch.init();
+
+#endif // TouchLib
+}
+
+bool touch_has_signal()
+{
+#if defined(TOUCH_XPT2046)
+  return ts.tirqTouched();
+
+#elif defined(TOUCH_MODULE_ADDR) // TouchLib
+  // TODO: implement TOUCH_INT
+  return true;
+#endif                           // TouchLib
+
+  return false;
+}
+
+void translate_touch_raw()
+{
+  if (touch_swap_xy)
+  {
+    touch_last_x = map(touch_raw_y, touch_map_x1, touch_map_x2, 0, touch_max_x);
+    touch_last_y = map(touch_raw_x, touch_map_y1, touch_map_y2, 0, touch_max_y);
+  }
+  else
+  {
+    touch_last_x = map(touch_raw_x, touch_map_x1, touch_map_x2, 0, touch_max_x);
+    touch_last_y = map(touch_raw_y, touch_map_y1, touch_map_y2, 0, touch_max_y);
+  }
+  // Serial.printf("touch_raw_x: %d, touch_raw_y: %d, touch_last_x: %d, touch_last_y: %d\n", touch_raw_x, touch_raw_y, touch_last_x, touch_last_y);
+}
+
+bool touch_touched()
+{
+#if defined(TOUCH_XPT2046)
+  if (ts.touched())
+  {
+    TS_Point p = ts.getPoint();
+    touch_raw_x = p.x;
+    touch_raw_y = p.y;
+    int max_z = p.z;
+    int count = 0;
+    while ((ts.touched()) && (count < TOUCH_XPT2046_SAMPLES))
+    {
+      count++;
+
+      TS_Point p = ts.getPoint();
+      if (p.z > max_z)
+      {
+        touch_raw_x = p.x;
+        touch_raw_y = p.y;
+        max_z = p.z;
+      }
+      // Serial.printf("touch_raw_x: %d, touch_raw_y: %d, p.z: %d\n", touch_raw_x, touch_raw_y, p.z);
+    }
+    translate_touch_raw();
+    return true;
+  }
+#elif defined(TOUCH_MODULE_ADDR) // TouchLib
+  if (touch.read())
+  {
+    TP_Point t = touch.getPoint(0);
+    touch_raw_x = t.x;
+    touch_raw_y = t.y;
+
+    touch_last_x = touch_raw_x;
+    touch_last_y = touch_raw_y;
+
+    translate_touch_raw();
+    return true;
+  }
+
+#endif // TouchLib
+
+  return false;
+}
+
+bool touch_released()
+{
+#if defined(TOUCH_XPT2046)
+  return true;
+
+#elif defined(TOUCH_MODULE_ADDR) // TouchLib
+  return false;
+#endif                           // TouchLib
+
+  return false;
+}

CYD-Klipper/src/core/klipper-serial/serial_klipper_printer_integration.cpp

@@ -271,9 +271,15 @@ int SerialKlipperPrinter::get_power_devices_count()
 bool SerialKlipperPrinter::set_power_device_state(const char* device_name, bool state)
 {
     String request = "/machine/device_power/device?device=" + urlEncode(device_name) + "&action=" + (state ? "on" : "off");
-    return make_serial_request_nocontent(HttpGet, request.c_str());
+    return make_serial_request_nocontent(HttpPost, request.c_str());
 }
 
+#ifdef CYD_S3
+#define MAX_FILE_LIST_SIZE 200
+#else
+#define MAX_FILE_LIST_SIZE 20
+#endif
+
 Files SerialKlipperPrinter::get_files()
 {
     Files files_result = {0};
@@ -291,7 +297,7 @@ Files SerialKlipperPrinter::get_files()
         return files_result;
     }
 
-    parse_file_list(doc, files, 20);
+    parse_file_list(doc, files, MAX_FILE_LIST_SIZE);
     
     files_result.available_files = (char**)malloc(sizeof(char*) * files.size());
 

CYD-Klipper/src/ui/macros.cpp

@@ -47,8 +47,7 @@ int macros_add_macros_to_panel(lv_obj_t * root_panel, BasePrinter* printer)
 
 static void power_device_toggle(lv_event_t * e)
 {
-    auto state = lv_obj_get_state(lv_event_get_target(e));
+    bool checked = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    bool checked = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
     DoubleStorage* device = (DoubleStorage*)lv_event_get_user_data(e);
     LOG_F(("Power Device: %s, State: %d -> %d\n", device->power_device_name, !checked, checked))
 

CYD-Klipper/src/ui/panels/settings_panel.cpp

@@ -15,8 +15,7 @@
 #endif // REPO_VERSION
 
 static void invert_color_switch(lv_event_t * e){
-    auto state = lv_obj_get_state(lv_event_get_target(e));
+    bool checked = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    bool checked = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
     global_config.printer_config[global_config.printer_index].invert_colors = checked;
     write_global_config();
     set_invert_display();
@@ -46,16 +45,14 @@ static void reset_ip_click(lv_event_t * e){
 }
 
 static void light_mode_switch(lv_event_t * e){
-    auto state = lv_obj_get_state(lv_event_get_target(e));
+    bool checked = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    bool checked = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
     get_current_printer()->printer_config->light_mode = checked;
     write_global_config();
     set_color_scheme();
 }
 
 static void filament_move_mode_switch(lv_event_t * e){
-    auto state = lv_obj_get_state(lv_event_get_target(e));
+    bool checked = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    bool checked = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
     get_current_printer()->printer_config->custom_filament_move_macros = checked;
     write_global_config();
 }
@@ -97,51 +94,44 @@ static void wake_timeout_dropdown(lv_event_t * e){
 }
 
 static void dualusb_screen_fix_switch(lv_event_t* e){
-    auto state = lv_obj_get_state(lv_event_get_target(e));
+    bool checked = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    bool checked = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
     global_config.display_mode = checked;
     write_global_config();
     ESP.restart();
 }
 
 static void disable_m117_messaging_switch(lv_event_t* e){
-    auto state = lv_obj_get_state(lv_event_get_target(e));
+    bool checked = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    bool checked = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
     global_config.disable_m117_messaging = checked;
     write_global_config();
 }
 
 static void sort_macros_switch(lv_event_t* e){
-    auto state = lv_obj_get_state(lv_event_get_target(e));
+    bool checked = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    bool checked = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
     global_config.sort_macros = checked;
     write_global_config();
 }
 
 static void show_estop_switch(lv_event_t* e){
-    auto state = lv_obj_get_state(lv_event_get_target(e));
+    bool checked = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    bool checked = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
     global_config.show_estop = checked;
     write_global_config();
 }
 
 static void full_filenames_switch(lv_event_t* e){
-    auto state = lv_obj_get_state(lv_event_get_target(e));
+    bool checked = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    bool checked = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
     global_config.full_filenames = checked;
     write_global_config();
 }
 
 static void double_size_gcode_img_switch(lv_event_t* e){
-    auto state = lv_obj_get_state(lv_event_get_target(e));
+    bool checked = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    bool checked = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
     global_config.double_size_gcode_img = checked;
     write_global_config();
 }
 
 static void rotate_screen_switch(lv_event_t* e){
-    auto state = lv_obj_get_state(lv_event_get_target(e));
+    bool checked = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    bool checked = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
     global_config.rotate_screen = checked;
     global_config.screen_calibrated = false;
     write_global_config();
@@ -149,8 +139,7 @@ static void rotate_screen_switch(lv_event_t* e){
 }
 
 static void on_during_print_switch(lv_event_t* e){
-    auto state = lv_obj_get_state(lv_event_get_target(e));
+    bool checked = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    bool checked = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
     global_config.on_during_print = checked;
     check_if_screen_needs_to_be_disabled();
     write_global_config();
@@ -161,15 +150,13 @@ static void btn_ota_do_update(lv_event_t * e){
 }
 
 static void auto_ota_update_switch(lv_event_t* e){
-    auto state = lv_obj_get_state(lv_event_get_target(e));
+    bool checked = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    bool checked = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
     global_config.auto_ota_update = checked;
     write_global_config();
 }
 
 static void multi_printer_switch(lv_event_t* e){
-    auto state = lv_obj_get_state(lv_event_get_target(e));
+    bool checked = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    bool checked = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
     global_config.multi_printer_mode = checked;
     write_global_config();
     nav_buttons_setup(PANEL_SETTINGS);

CYD-Klipper/src/ui/panels/temp_panel.cpp

@@ -161,9 +161,7 @@ static void set_temp_via_preset(lv_event_t * e){
 }
 
 static void btn_toggleable_edit(lv_event_t * e){
-    lv_obj_t * btn = lv_event_get_target(e);
+    temp_edit_mode = lv_obj_has_state(lv_event_get_target(e), LV_STATE_CHECKED);
-    auto state = lv_obj_get_state(btn);
-    temp_edit_mode = (state & LV_STATE_CHECKED == LV_STATE_CHECKED);
 }
 
 static void btn_retract(lv_event_t * e){

CYD-Klipper/src/ui/serial/serial_console.cpp

@@ -5,11 +5,49 @@
 
 #define MAX_COMDLINE_SIZE 80
 #define MAX_WORDS 6
+#define BACKSPACE_CHAR 0x08
+#define ESCAPE_CHAR '\x1b'
+#define CSI_CHAR '['
+#define LEFT_ARROW_CHAR 'D'
+#define RIGHT_ARROW_CHAR 'C'
+#define DELETE_KEY_1_CHAR '3'
+#define DELETE_KEY_2_CHAR '~'
+#define PRINT_CHAR_START 32
+#define PRINT_CHAR_END 126
 
 namespace serial_console
 {
     bool global_disable_serial_console = false;
 
+    /**
+     * @brief Redraws the characters from the current cursor position to the end of the buffer on the serial console.
+     *
+     * This function is used to update the terminal display when characters are inserted or deleted
+     * in the middle of the input buffer. It:
+     *   - Saves the current cursor position
+     *   - Clears the line from the cursor to the end
+     *   - Prints characters from 'cur' to 'len'
+     *   - Restores the original cursor position
+     *
+     * @param cur Current cursor position within the buffer
+     * @param len Current length of the buffer (number of characters entered)
+     * @param buf Character buffer containing the input string
+     */
+    static inline void redraw(const int cur, const int len, char *buf) {
+        if (!temporary_config.remote_echo)
+            return;
+
+        Serial.print("\x1b[s");
+        Serial.print("\x1b[K");
+
+        // Reprint characters from cur to end
+        for (int i = cur; i < len; i++) {
+            Serial.print((char)buf[i]);
+        }
+
+        Serial.print(" \x1b[u");
+    }
+
     /*
      * read_string_until: Non-blocking replacement for Serial.readStringUntil()..
      * With delimeter '\n' acts as 'read line'.
@@ -20,6 +58,7 @@ namespace serial_console
     bool read_string_until(char delimiter, char *result, int max_len)
     {
         static int index = 0;
+        static int cur = 0;
         int c;         // read character, -1 if none
         int cnt = 100; // limit on amount of iterations in one go; we're supposed to be non-blocking!
 
@@ -28,43 +67,75 @@ namespace serial_console
             --cnt;
 
             // backspaceF
-            if (c == 8)
+            if (c == BACKSPACE_CHAR && cur > 0) {
-            {
+                    // shift characters left from cursor position
-                if (index > 0)
+                    memmove(&result[cur - 1], &result[cur], index - cur);
-                {
-                    if(temporary_config.remote_echo) Serial.print("\x08 \x08"); // overwrite last character with space and move cursor 1 back.
                     index--;
-                }
+                    cur--;
+                    // move cursor left on terminal and redraw updated string
+                    if(temporary_config.remote_echo) Serial.print("\x1b[D");
+                    redraw(cur, index, result);
+            // handle ANSI escape sequences (arrow keys, delete key)
+            } else if (c == ESCAPE_CHAR) {
+
+                if ((c = Serial.read()) == -1)
+                    break;
+
+                // Expect '[' character
+                if (c != CSI_CHAR)
                     continue;
+
+                if ((c = Serial.read()) == -1)
+                    break;
+
+                // Left arrow key
+                if (c == LEFT_ARROW_CHAR && cur > 0) {
+                    // move cursor left on terminal
+                    if(temporary_config.remote_echo) Serial.print("\x1b[D");
+                    cur--;
+                // Right arrow key
+                } else if(c == RIGHT_ARROW_CHAR && cur < index) {
+                    // move cursor right on terminal
+                    if(temporary_config.remote_echo) Serial.print("\x1b[C");
+                    cur++;
+                // Delete key
+                } else if(c == DELETE_KEY_1_CHAR) {
+                    if ((c = Serial.read()) == -1)
+                        break;
+                    if (c == DELETE_KEY_2_CHAR && cur < index) {
+                        memmove(&result[cur], &result[cur + 1], index - cur - 1);
+                        index--;
+                        redraw(cur, index, result);
+                    }
                 }
 
-            if(temporary_config.remote_echo) Serial.print((char)c); // echo
+            // Handle printable characters
-
+            } else if (c >= PRINT_CHAR_START && c <= PRINT_CHAR_END) {
-            // Buffer overflow handling:
+                // Append character at the end
-            // start treating current buffer as invalid:
+                if (index < max_len - 1 && cur == index) {
-            // - stop collecting more data
+                    if(temporary_config.remote_echo) Serial.print((char)c);
-            // - return false on delimeter, flushing everything collected,
+                    result[index++] = c;
-            // - restart collection from scratch after delimeter,
+                    cur++;
-            // - return control as normal.
+                // Insert character in the middl
-
+                } else if (index < max_len - 1) {
-            if (index >= max_len - 1)
+                    memmove(&result[cur + 1], &result[cur], index - cur);
-            {
+                    result[cur] = c;
-                if (c == delimiter) // got delimeter: flush buffer quietly, restart collection.
+                    index++;
-                {
+                    if(temporary_config.remote_echo) Serial.print((char)c);
+                    cur++;
+                    redraw(cur, index, result);
+                } else if (c == delimiter) { // got delimeter: flush buffer quietly, restart collection.
                     index = 0;
+                    cur = 0;
                     return false;
                 }
-                else
-                    continue; // discard any data past the end of the buffer, keep reading
-            }
-
-            result[index++] = c;
-
             // delimiter was found
-            if (c == delimiter)
+            } else if (c == delimiter) {
-            {
+
+                if(temporary_config.remote_echo) Serial.println();
                 result[index] = '\0'; // Null-terminate the string
                 index = 0;
+                cur = 0;
                 return true; // Success: Delimiter found
             }
         }

ci.json

@@ -0,0 +1,67 @@
+{
+    "esp32-2432S024C-SD": {
+        "name": "ESP32-2432S024 (2.4\" Capacitive)",
+        "site": true,
+        "s3": false
+    },
+    "esp32-2432S028R": {
+        "name": "ESP32-2432S028 (2.8\" Resistive)",
+        "site": true,
+        "s3": false,
+        "default": true
+    },
+    "esp32-2432S032C-SD": {
+        "name": "ESP32-2432S032 (3.2\" Capacitive)",
+        "site": true,
+        "s3": false
+    },
+    "esp32-3248S035C": {
+        "name": "ESP32-3248S035 (3.5\" Capacitive)",
+        "site": true,
+        "s3": false
+    },
+    "esp32-3248S035C-V": {
+        "name": "ESP32-3248S035 (3.5\" Capacitive) Vertical Orientation",
+        "site": true,
+        "s3": false
+    },
+    "esp32-4827S043C-SD": {
+        "name": "ESP32-4827S043 (4.3\" 480x270 Capacitive)",
+        "site": true,
+        "s3": true
+    },
+    "esp32-8048S043C-SD": {
+        "name": "ESP32-8048S043 (4.3\" 800x480 Capacitive)",
+        "site": true,
+        "s3": true
+    },
+    "esp32-8048S043C-SD-alt": {
+        "name": "ESP32-8048S043 Alt (4.3\" 800x480 Capacitive)",
+        "site": true,
+        "s3": true
+    },
+    "esp32-CROWPANEL-28R": {
+        "name": "ESP32-CROWPANEL-28R (2.8\" Resistive)",
+        "site": true,
+        "s3": false,
+        "brand": "CrowPanel"
+    },
+    "esp32-CROWPANEL-35C": {
+        "name": "ESP32-CROWPANEL-35C (3.5\" Capacitive)",
+        "site": true,   
+        "s3": true,
+        "brand": "CrowPanel"
+    },
+    "esp32-JC4827W543C": {
+        "name": "ESP-JC4827W543C (4.3\" Capacitive)",
+        "site": true,
+        "s3": true,
+        "brand": "Guition"
+    },
+    "esp32-JC8048W550": {
+        "name": "Guition JC8048W550 (5\" Capacitive)",
+        "site": true,
+        "s3": true,
+        "brand": "Guition"
+    }
+}

ci.py

@@ -1,40 +1,19 @@
 import subprocess, os, shutil, json
 
-CYD_PORTS = [
-    "esp32-3248S035C", 
-    "esp32-2432S028R", 
-    "esp32-2432S032C-SD", 
-    "esp32-8048S043C-SD",
-    "esp32-8048S043C-SD-alt", 
-    "esp32-2432S024C-SD", 
-    "esp32-4827S043C-SD",
-    "esp32-3248S035C-V",
-    #"esp32-4827S043R-SD",
-    "esp32-CROWPANEL-28R",
-    "esp32-CROWPANEL-35C",
-]
-
-ESP_S3_CHIPS = [
-    "esp32-8048S043C-SD",
-    "esp32-8048S043C-SD-alt",
-    "esp32-4827S043C-SD",
-    "esp32-CROWPANEL-35C",
-]
-
 BASE_DIR = os.getcwd()
 
-def get_manifest(base_path : str, device_name : str):
+def get_manifest(base_path : str, device_name : str, is_s3 : bool):
     return {
         "name": f"to {device_name}",
         "funding_url": "https://ko-fi.com/suchmememanyskill",
         "new_install_prompt_erase": True,
         "builds": [
             {
-                "chipFamily": "ESP32-S3" if device_name in ESP_S3_CHIPS else "ESP32",
+                "chipFamily": "ESP32-S3" if is_s3 else "ESP32",
                 "parts": [
                     {
                         "path": f"{base_path}/bootloader.bin",
-                        "offset": 0 if device_name in ESP_S3_CHIPS else 0x1000 
+                        "offset": 0 if is_s3 else 0x1000 
                     },
                     {
                         "path": f"{base_path}/partitions.bin",
@@ -59,6 +38,7 @@ def extract_commit() -> str:
 
 repo_version = extract_commit()
 configurations = []
+site_sections : dict[str, dict] = {"CYD": []}
 
 def add_configuration(board : str):
     configurations.append({
@@ -67,10 +47,32 @@ def add_configuration(board : str):
         "URL": f"https://suchmememanyskill.github.io/CYD-Klipper/out/{board}/firmware.bin"
     })
 
+def add_site_section(port : str, data : dict[str, bool|str]):
+    brand = data["brand"] if "brand" in data else "CYD"
+    
+    if brand not in site_sections:
+        site_sections[brand] = []
+
+    site_sections[brand].append({
+        "name": data["name"],
+        "port": port,
+        "default": "default" in data and data["default"],
+    })
+
 if os.path.exists("out"):
     shutil.rmtree("out")
 
-for port in CYD_PORTS:
+if not os.path.exists("_site"):
+    os.makedirs("_site")
+
+with open("./ci.json", "r") as fp:
+    ci_data : dict[str, dict[str, bool|str]] = json.load(fp)
+
+for port, data in ci_data.items():
+    if "skip" in data and data["skip"]:
+        print(f"Skipping {port}...")
+        continue
+
     port_path = f"out/{port}"
     os.chdir(BASE_DIR)
     os.makedirs(port_path, exist_ok=True)
@@ -82,18 +84,21 @@ for port in CYD_PORTS:
 
     shutil.copy(os.path.join(os.path.expanduser("~"), ".platformio/packages/framework-arduinoespressif32/tools/partitions/boot_app0.bin"), f"{port_path}/boot_app0.bin")
     os.chdir(port_path)
-    if (port in ESP_S3_CHIPS):
+    if (bool(data["s3"])):
-        subprocess.run(["python3", "-m", "esptool", "--chip", "esp32s3", "merge_bin", "-o", "merged_firmware.bin", "--flash_mode", "dio", "--flash_freq", "80m", "--flash_size", "16MB", "0x0000", "bootloader.bin", "0x8000", "partitions.bin", "0xe000", "boot_app0.bin", "0x10000", "firmware.bin"], check=True)
+        subprocess.run(["esptool", "--chip", "esp32s3", "merge_bin", "-o", "merged_firmware.bin", "--flash_mode", "dio", "--flash_freq", "80m", "--flash_size", "16MB", "0x0000", "bootloader.bin", "0x8000", "partitions.bin", "0xe000", "boot_app0.bin", "0x10000", "firmware.bin"], check=True)
     else:    
-        subprocess.run(["python3", "-m", "esptool", "--chip", "esp32", "merge_bin", "-o", "merged_firmware.bin", "--flash_mode", "dio", "--flash_freq", "40m", "--flash_size", "4MB", "0x1000", "bootloader.bin", "0x8000", "partitions.bin", "0xe000", "boot_app0.bin", "0x10000", "firmware.bin"], check=True)
+        subprocess.run(["esptool", "--chip", "esp32", "merge_bin", "-o", "merged_firmware.bin", "--flash_mode", "dio", "--flash_freq", "40m", "--flash_size", "4MB", "0x1000", "bootloader.bin", "0x8000", "partitions.bin", "0xe000", "boot_app0.bin", "0x10000", "firmware.bin"], check=True)
 
     os.chdir(BASE_DIR)
 
     with open(f"./_site/{port}.json", "w") as f:
-        json.dump(get_manifest(port_path, port), f)
+        json.dump(get_manifest(port_path, port, bool(data["s3"])), f)
 
     add_configuration(port)
 
+    if "site" in data and data["site"]:
+        add_site_section(port, data)
+
 os.chdir(BASE_DIR)
 out_dir = "./_site/out"
 if os.path.exists(out_dir):
@@ -102,3 +107,16 @@ shutil.copytree("./out", out_dir)
 
 with open("./_site/OTA.json", "w") as f:
     json.dump({"Configurations": configurations}, f)
+
+with open("./_site/index.html", "w") as fp:
+    with open("./template.html", "r") as template_fp:
+        template = template_fp.read()
+
+    insert_html = ""
+    
+    for brand, sections in site_sections.items():
+        option_htmls = [f"<option {'selected' if x['default'] else ''} value=\"{x['port']}\">{x['name']}</option>" for x in sections]
+        section_html = f"<optgroup label=\"{brand}\">{''.join(option_htmls)}</optgroup>"
+        insert_html += section_html
+
+    fp.write(template.replace("{{%PORTS%}}", insert_html))

template.html

@@ -132,15 +132,7 @@
       <h3><span class="iconify" data-icon="mdi-download"></span> Install</h3>
       <p>Select your device from the list below and click 'Connect'.<br>Note: You may need to hold the 'BOOT' button on the device while pressing install.<br><br>The 2.8" Resistive and 3.5" Capacitive models are best suited (in my opinion) for CYD-Klipper.<br><br>Note for any resistive models: You can clear touch calibration by holding the BOOT button for 8 seconds while the screen is on.</p>
       <select id="select-install-btn" onchange="setInstallButton(getElementById('select-install-btn').value)">
-        <option value="esp32-2432S024C-SD">ESP32-2432S024 (2.4" Capacitive)</option>
+            {{%PORTS%}}
-        <option selected value="esp32-2432S028R">ESP32-2432S028 (2.8" Resistive)</option>
-        <option value="esp32-2432S032C-SD">ESP32-2432S032 (3.2" Capacitive)</option>
-        <option value="esp32-3248S035C">ESP32-3248S035 (3.5" Capacitive)</option>
-        <option value="esp32-3248S035C-V">ESP32-3248S035 (3.5" Capacitive) Vertical Orientation</option>
-        <option value="esp32-4827S043C-SD">ESP32-4827S043 (4.3" 480x270 Capacitive)</option>
-        <option value="esp32-8048S043C-SD">ESP32-8048S043 (4.3" 800x480 Capacitive)</option>
-        <option value="esp32-8048S043C-SD-alt">ESP32-8048S043 Alt (4.3" 800x480 Capacitive)</option>
-        <option value="esp32-CROWPANEL-28R">ESP32-CROWPANEL-28R (2.8" Resistive)</option>
       </select>
       <span id="install-btn"></span>
     </section>

test_printer/docker-compose.yml

@@ -4,7 +4,7 @@ services:
     ports:
       - "7125:7125"
       - "8110:8110"
-    image: ghcr.io/mainsail-crew/virtual-klipper-printer:master
+    image: ghcr.io/mainsail-crew/virtual-klipper-printer:latest
   webui:
     container_name: mainsail
     volumes: